Hall Effect Sensors - Page 7 - Mega Sale! Save up to 29%
Mega Sale! Up to 29% off on Hall Effect Sensors at Wise Warthog, Page 7. Top brands include Honeywell, MELEXIS, Phares Electronics, ALLEGRO MICROSYSTEMS, HONEYWELL S&C, Diybigworld, DIODES, Exiron, Allegro MicroSystems, Aexit, Taidacent, & Siemens. Hurry! Limited time offers. Offers valid only while supplies last.
HONEYWELL S&C SS513AT HALL EFFECT SENSOR BIPOLAR, SOT89B-4 (100 pieces)
4.2 out of 5 stars with 53 reviews
Magnetic Type: Bipolar Family: SS513AT Supplier_Package: SOT-89 Packaging: Tape and Reel Maximum Output Current: 20 mA Pin_Count: 4 Mounting: Surface Mount Operating Temperature: -40 to 150 °C Dimension: 4.4 x 2.4 x 1.4 mm.
Zero Speed Sensor, 103SR Series, Hall Effect, 4 to 24 Vdc, Open Drain MOFSET Output
4.7 out of 5 stars with 34 reviews
The Honeywell ZH10 Hall-Effect Zero Speed Sensor provides a durable, cost-effective solution in most harsh environments. The sensor is available in a 15/32'' (11.9 mm) diameter, in a 1.0'' (25.4 mm) length. The aluminum package is simple to install and adjust and does not require rotational orientation.Features:Thread Type: 15/32 UNS-2AThread Length: 1.0'' (25.4 mm)Low cost Omni-directional sensor to target orientationDigital outputSmall sizeLow power consumptionAluminum package is simple to
Phares Hall Effect Sensor for High Temperature Industrial Environments, 10' Cable
4.6 out of 5 stars with 32 reviews
Phares Electronics Digital Output Hall Effect Sensors are simple on/off non-contact switching devices. Digital output signal is clean, fast and switched without bounce - an inherent problem with mechanical contact switches. They are magnetically activated switches that detect the motion, position, or change in field strength of an electromagnet, a permanent magnet, or a ferromagnetic material with an applied magnetic bias. The digital output is a square-wave signal that is directly proportional
DIODES AH183-WG-7 AH183 Series 5.5 V Low Power Hall Effect Switch Surface Mount - SC-59 - 3000 item(s)
4.4 out of 5 stars with 10 reviews
AH183 Series 5.5 V Low Power Hall Effect Switch Surface Mount - SC-59 ***** For more information refer to the specification sheet located in the 'Downloads' section below the image *****MagneticHallEffectType: Hall Switch / Latch. OutputCurrent: 10 mA. SupplyVoltage: 2.5 to 5.5 V. SupplyCurrent: 280 to 500 µA. OperatingTempRange: -40 to +85 °C.
Allegro Microsystems A1302KUA-T Hall Effect Sensor, 5 Volt, 10 mA (Pack of 4)
4.1 out of 5 stars with 125 reviews
The a1302 is a continuous-time, ratio metric, linear hall-effect sensor ICS. It is optimized to accurately provide a voltage output that is proportional to an applied magnetic field. These devices have a quiescent output voltage that is 50 percent of the supply voltage. Output sensitivity is 1.3 mV/G typical for the a1302. Operating supply voltage: 4.5V to 6.0V. Output current: 10MA. Low-noise output. Fast power-on time. Ratio metric rail-to-rail output. Solid-state reliability.Operating temp
Aexit 5Pcs SS41F 4.5-24V 3 Terminals Bipolar Hall Effect Sensor Magnetic Detector
4.4 out of 5 stars with 43 reviews
Stability for Automotive or Industrial Applications.Open-Collector 25 mA Output. Compatible with Digital Logic.Reverse Battery Protection.Solid-State Reliability.Resistant to Physical Stress.Activate with Small, Commercially Available Permanent Magnets.Product Name : Hall Effect Sensor;Model : SS41F;Voltage : 4.5-24V. Output Current : 25mA;Temperature Range : -40C - +150C. Terminals Number : 3;Terminals Length : 15mm/0.59''. Size : 19mmmx 4mm x 1.5mm/0.75'' x 0.16'' x 0.06''(L*W*T);Material :
2pcs lot wcs1700 100A hall effect current transducer hall effect sensor circuit inductive current sensor
4.8 out of 5 stars with 147 reviews
First, size: length 37mmX width 31mmX height 16.5mm Second, the working voltage: DC DC 5V Third, characteristics: 1, with signal output instructions; 2, output over-current signal indication; 3, with a mounting hole to facilitate the firmware installation; 4, sampling current conversion analog signal output, can be connected to the ADC, TTL level signal output, can be connected to the microcontroller IO port control. 5, the output signal is: analog signal and level signalhall effect sensor.